MGE Office Protection Systems Eaton Corporation’s acquisition of MGE Office Protection Systems (November 2007) created a larger, stronger power quality business with a globally enhanced competitive position and a wide range of products, expertise and resources. Through the acquisition, Eaton has secured its position as the world’s second-largest manufacturer and supplier of single-phase UPS products, delivering even greater value to its customers. In fact, the majority of Fortune 500 companies relies on Eaton for its power protection, distribution and management solutions. MGE Office Protection Systems products are a part of the Pulsar Series of solutions offered by Eaton. The products are designed and manufactured to offer secured power and data protection conditioners for enterprises, small business and homes, with a range of, and.
Documentation and replacement UPS products Visit our to download manuals and to see which current Eaton UPS is the most likely replacement model.
. Pulsar M 2200 RT 2U 2200 RT 3U 3000 RT 2U 3000 RT 3U 3000 RT 3U XL EXB RT 3U Installation and user manual - Page 1 34003641FR/AA. Page 2 34007776EN/AB. Before installing Pulsar M, please read the booklet on the required safety instructions. Then follow the indications in this manual. To discover the entire range of MGE UPS SYSTEMS products and the options available for the Pulsar M range, we invite you to visit our web site at www.mgeups.com or contact your MGE UPS SYSTEMS representative. Introduction Pictograms Important instructions that must always be followed.
Information, advice, help. Visual indication. Audio signal. In the illustrations on the following pages, the symbols below are used: LED off LED on LED flashing - Page 4 34007776EN/AB. Presentation Standard positions. 6 Tower position. 6 Rack position.
6 Rear panels. 7 Pulsar M 2200 / 3000. 7 Pulsar M EXB (optional battery module).
7 Control panel. 7 Installation Unpacking and contents check.
8 Installation in tower position. 9 Installation in rack position. Tower position Rack position - Page 6 34007776EN/AB Dimensions (H x W x D) in mm Pulsar M 2200 RT 2U 440 x 86 x 640 Pulsar M 2200 RT 3U 440 x 131 x 490 Pulsar M 3000 RT 2U.
1.2 Rear panels Pulsar M 2200 / 3000 Pulsar M EXB (optional battery module) 1.3 Control panel 1. Presentation (1) USB communication port (2) RS232 communication port (3) Connector for automatic recognition of an additional battery module (4) Slot for optional communication card (5) Connector for remote ON/OFF and RPO (Remote Power Off) control (6) Connector for additional battery module.
Global Operations No CD Cracks Crack for Version 1.0 ENG Crack for Version 2.0 ENG Return to the No CD Cracks for PC Games Section. Global Operations Global Ops: System. Global Operations [ENGLISH] No-CD/Fixed Image; Global Operations v2.0 [US] No-CD/Fixed. Official Global Operations v2.0. Global operations cd crack. JontMaster Backup CD Global Operations All Global Operations v1.1 Global Operations v1.2 Global Operations v2.0 Global Operations v2.0 US Global Operations v1.2 US.
Installation 2.1 Unpacking and contents check (30) Pulsar M 2200 or 3000 UPS (31) connection cable to AC-power source (32) 2 connection cables for the protected equipment (33) RS232 communications cable (34) USB communications cable (35) 2 systems to secure power plugs (36) Solution-Pac CD-ROM (37) Documentation Packing materials must be disposed of in compliance with all local regulations concerning waste. It is advised to first install the battery module, then the power module above. Follow steps 1 to 4 for module mounting on the rails. The rails and necessary hardware are supplied by MGE UPS SYSTEMS.
Installation - Page 9. Installation 2.4 Communication ports Connection of RS232 or USB communication port (optional) The RS232 and USB communication ports cannot operate simultaneously. Installation of the communication cards (optional) - Page 6EN/AB 1 - Connect the RS232 (33) or USB (34) communication cable to the serial or USB port on the computer equipment. 2.5 Connections with a FlexPDU (Power Distribution Unit) module (optional) 2.6 Connections with a HotSwap MBP module (optional) The HotSwap MBP module makes it possible to service or even replace the UPS without affecting the connected loads (HotSwap function). Installation 1 - Connect the UPS socket (10) to the AC- power source using the cable (31) supplied. Installation HotSwap MBP-module operation UPS start-up with the HotSwap MBP module 1 - Check that the UPS is correctly connected to the HotSwap MBP module. 2 - Set switch (53) to the Normal position.
3 - Start the UPS by pressing the ON/OFF button (27) on the UPS control panel. The load is supplied by the UPS. If UPS personalisation is desired, it is advised to enter the personalisation mode at this time. This mode may be entered using the buttons on the control panel or the Personal Solution-Pac software (Windows) included on the Solution-Pac CD-ROM provided by MGE UPS SYSTEMS. 3.2 Operation on battery power. Pulsar has the choice of two remote control options. ◗ RPO: Remote Power Off allows a remote contact to be used to disconnect all the equipment connected to the UPS from the power supply.
Restarting the UPS requires manual intervention. Contact open: shut down of UPS Contact closed: start-up of UPS (UPS connected to the network and network energized) Note: local On/Off control via button (27) has priority over the remote control order. Contact open: shut down of UPS To return to normal operation, deactivate the external remote shut down contact and restart the UPS using button (27). Access to measurements and personalisation data 4.1 Display menus arrangement 4.2 Access to measurements Press the scroll button (25) to access any status conditions and alarms, then the measurements for voltage, current, frequency, power output and battery backup time. 4.3 Personalisation using the control panel Local personalisation Function.
Pulsar Evolution 2200
Access to measurements and personalisation data Output personalisation Function Output voltage Frequency converter Output frequency Transfer to the bypass AC input Overload level (1) These parameters may be modified only when the UPS is OFF. Detailed comments are available in the Personal Solution-Pac software. ON/OFF personalisation Function Start on battery power. Maintenance 5.1 Troubleshooting If LED (21) or (22) is ON, a fault or an alarm has occurred. Use the escape button (24) to stop the audio alarm.
Indication The UPS does not start, the alphanumeric display indicates: COLD START NOK CHECK AC WIRING LED (22) is ON, the SWF LED (11) at the rear of the UPS is ON. Troubleshooting a UPS equipped with the HotSwap MBP module Indication The load is no longer supplied when the rotary switch (49) on the HotSwap MBP module is set to the Bypass position. The load is no longer supplied when the rotary switch (49) on the HotSwap MBP module is set to the Normal position. Mounting the new battery module Carry out the above instructions in reverse order.
◗ To ensure safety and high performance, use only batteries supplied by MGE UPS SYSTEMS. ◗ Take care to firmly press together the two parts of the connector during remounting. 5.4 Training centre To fully master operation of your MGE UPS SYSTEMS product and carry out level 1 servicing, see our complete range of technical training courses, available in both French and English. 50 Hz training centre 60 Hz training centre. Appendices 6.1 Technical specifications Output power Electrical supply network ◗ Rated input voltage ◗ Input voltage range ◗ Frequency ◗ Power factor ◗ Leakage current Load output ◗ Voltage ◗ Frequency ◗ Harmonic distortion ◗ Overload capacity ◗ Current Battery Environment ◗. 6.2 Glossary Bypass AC input Backup time Battery test Equipments Excessive discharge FlexPDU Frequency converter HotSwap MBP Low-battery warning Normal AC input Percent load Personalisation Programmable outlets Start on battery power UPS ON/OFF controlled by software Bypass line from the AC-power source, controlled by the UPS, used to directly supply the load if an overload or a malfunction occurs on the UPS. MGE UPS SYSTEMS T H E U N I N T E R R U P T I B L E P O W E R P R O V I D E R 140, Avenue Jean Kuntzmann ZIRST - Montbonnot St Martin 38334 - Saint Ismier Cedex - France www.mgeups.com.
. page 6. page 35. page 63. page 91.
page 119. page 147.
Mge Pulsar Evolution 2200 Ups
Download software and firmware Whether you’d like to monitor a single UPS or help with managing your entire virtualized network, Eaton has a monitoring and management software solution. From monitoring event history, notifying you of alerts and delivering real-time status, Eaton software provides the tools you need to keep your critical equipment running at all times. Our software solutions are easy to use and maintain business continuity which saves time, saves money and reduces risk. Use the drop down menus below to select a specific product to see related software and firmware solutions or filter the results using the “solution type” drop down to show only software, firmware or legacy software. Or select your software solution: View a complete listing of our software & firmware products.